Skip to main content

kirpa

What Do Home Inspectors Look For? A Brampton Buyer's Room-by-Room Checklist

You'll spend about four hours standing in a house you don't own yet, watching a stranger open panels and poke at things with a flashlight. Then he hands you a report, and you have maybe two days to decide whether to buy.

So what is he actually looking at?

Here's the honest version, from the inspector's side of the flashlight.

A home inspector looks for the things that cost real money and the things that can hurt you: water where it shouldn't be, structure that's moving, wiring that can start a fire, heating that's near the end of its life, and air you shouldn't be breathing. Everything else is detail.

This is the room-by-room version of that, in the order Balwinder actually walks a house in Brampton.

First, What a Home Inspection Is Not

A home inspection is a visual, non-invasive check of the house on the day you're there. That one sentence explains most arguments buyers have later.

Non-invasive means the inspector doesn't open walls, lift carpet, move the seller's furniture, or dig up the yard. If the mold is behind finished basement drywall, a standard inspection can't see it. (More on that below, because it comes up a lot in Brampton.)

On the day means it's a snapshot. A furnace that runs fine in October can fail in January. The report tells you its age and condition, not its future.

Standard inspections also don't cover: pools and hot tubs, septic systems, underground oil tanks, wells, anything behind a locked door, and specialized testing — mold, asbestos, radon, WETT — unless you add it.

Ontario doesn't license home inspectors either. The province passed the Home Inspection Act in 2017 and never brought it into force, so "certified" means certified by somebody, and you should ask who.

That's the frame. Now the walk-through.

Outside: Roof, Walls, Grading

Balwinder starts outside, because the outside tells you what to look for inside.

Roof. Shingle condition, how many layers, flashing around the chimney and vents, sagging along the ridge. A roof near the end of its life in Brampton is a five-figure conversation, and it's the single most common item buyers use to negotiate.

Exterior walls and windows. Brick with cracked mortar, stucco or EIFS with no drainage (common on 2000s builds), rotted window frames, caulking that's gone. Every one of these is a water entry point.

Grading and drainage. Does the ground slope toward the foundation? Do the downspouts dump water right at the wall? This is boring and it's the number one cause of the wet basement you'll find later. It's also cheap to fix — which is why sellers rarely have.

Garage, deck, driveway. Railings, stairs, rot in deck posts, a garage door that doesn't auto-reverse. Safety items go in the report as safety items, not cosmetic ones.

Attic: The Part Most Buyers Never See

If you only read one section, read this one.

Buyers almost never go into the attic. Inspectors always do. Here's what Balwinder is checking up there:

  • Insulation depth. Brampton homes from the 1970s–90s often have half of what the current code calls for. That's a heating bill, not a defect, but you should know.
  • Ventilation. Soffit vents blocked by insulation, not enough roof vents, or none at all. A poorly vented attic in a GTA winter builds frost on the underside of the roof deck. That frost melts in March. Now you have "a roof leak" that isn't a roof leak.
  • Bathroom exhaust fans venting into the attic instead of outside. This is the one Balwinder finds most often on musty-smell calls. Every shower pumps warm, wet air into a cold space. Within a couple of winters, there's black staining on the sheathing above the bathroom. It looks like a roof problem. It's a $200 duct problem that turned into a mold problem.
  • Staining, daylight, animal activity. Water stains around the chimney and plumbing stacks, light coming through where it shouldn't, and evidence of raccoons or squirrels.

The bathroom-fan problem is the most Brampton-specific thing on this list, and it's the one thing a buyer can check on a showing: go in the bathroom, turn the fan on, and go outside to see if air comes out of a vent on the roof or wall. If you can't find one, ask the inspector to look for it first.

Structure and Foundation

Foundation walls. Cracks are normal in poured concrete; which cracks matter is the skill. Vertical hairline cracks from shrinkage are usually cosmetic. Horizontal cracks, stair-step cracks in block, or cracks with displacement (one side proud of the other) get flagged for a structural engineer.

Floors and framing. Sloping floors, doors that won't latch, cracks above door frames — signs the house has moved. Some settling in a 50-year-old house is expected. Movement that's ongoing is a different conversation.

Basement walls, finished. Here's the frustrating part. A finished basement hides the foundation. The inspector checks what's visible — the utility room, behind the furnace, any unfinished corner — and uses a moisture meter on the finished walls. If the meter spikes or the room smells musty, he'll tell you, but he can't cut the drywall.

That's where a mold inspection comes in. It's a separate service — $450–$750 depending on how many rooms are affected, one to two hours, and the air sampling and third-party lab analysis are included in that price rather than billed on top. If the house has a finished basement and any history of water, adding it is cheap insurance.

Electrical

The inspector opens the panel cover. Most buyers have never seen the inside of one.

He's looking for: panel size (60-amp service in a house full of modern appliances), aluminum branch wiring (1960s–70s), knob-and-tube (pre-1950 — mostly Toronto, not Brampton, but it exists in older pockets), double-tapped breakers, scorching, open junction boxes, missing GFCI protection in kitchens and bathrooms, and reversed polarity on outlets.

Two of those — aluminum wiring and knob-and-tube — matter beyond safety. Some insurers won't write a policy without remediation. Find out during the conditional period, not the week before closing.

Plumbing

Supply lines, drains, water heater, fixtures. The inspector runs every tap, flushes every toilet, fills and drains the tub, and watches.

What he's looking for:

  • Pipe material. Galvanized steel supply (rusts shut from the inside), Kitec (a 1995–2007 product that fails at the fittings and is a known insurance issue), polybutylene, cast iron drains that have gone thin.
  • Water pressure and drainage speed. Slow drains on the lowest level point at the main line.
  • Water heater. Age, rental or owned (most in Brampton are rentals — you inherit the contract), venting, signs of leaking.
  • Under every sink. Active leaks, past leaks, DIY repairs with the wrong fittings.
  • Sump pump. Does it run? Where does it discharge?

A sewer camera scope is a separate add-on. If the house is pre-1980 or has big trees near the front, it's worth it.

Heating and Cooling

Furnace age, condition, filter, venting, visible rust or corrosion in the heat exchanger area, and whether it actually fires. Same for the air conditioner, if it's above about 15°C outside — inspectors won't run an AC in cold weather because it can damage the compressor.

The number buyers care about is age. A mid-efficiency furnace from 2005 is at the end of its expected life. That doesn't mean it fails tomorrow. It means budget for it.

Also checked: thermostat operation, ductwork condition where visible, humidifier, and the exhaust vent on high-efficiency units (it should terminate outside, clear of windows and the gas meter).

Interior: Walls, Windows, Doors, Bathrooms

Room by room, quickly. Ceiling stains (past leaks — from the roof above, or the bathroom above). Windows that won't open, seals that have failed (foggy double-panes). Doors out of square. Bathroom tile and caulking, because a failed tub surround leaks into the floor below for years before anyone notices. Smoke and CO alarms — present, working, in the right places.

Fireplaces and wood stoves get a visual check. If there's a wood-burning appliance and you'll need insurance on it, that's a WETT inspection, which is a separate certified service. Ask before inspection day so it can be done in the same visit.

What the Four Hours Actually Look Like

Here's the thing none of the realtor articles tell you, because they've never done one.

A thorough inspection of a detached house in Brampton takes Balwinder about four hours. Roughly: 45 minutes outside and on the roof, 30 in the attic, an hour in the basement and mechanical room, and the rest room by room, with time at the end to walk you through what he found.

A "basic" inspection — 90 minutes, no attic entry, no panel cover off — costs less and finds less. We wrote about the difference between a basic and a thorough home inspector if you're comparing quotes and wondering why they're so far apart.

You should be there. Not for the whole four hours, but for the last hour. Reading a report is one thing. Standing in the basement while someone points at the crack is another.

What a Good Report Looks Like

It's long — 40 to 70 pages is normal — because it has photos of everything, including the things that are fine.

What to look for in it:

  1. A summary page that separates safety issues, major defects, and maintenance items. If everything's in one undifferentiated list, that's a lazy report.
  2. Photos with arrows. You should be able to find every flagged item yourself.
  3. Plain-language "what this means." Not just "efflorescence present on north foundation wall" but "this means water has been coming through here — check the grading and downspout outside this wall."
  4. Recommendations with a next step. "Have a licensed electrician evaluate" beats "concern noted."

What a report won't do is tell you whether to buy. That's your call. What it does is turn a gut feeling into a list with prices next to it, which is exactly what you need when you're deciding whether to waive the inspection to win a bidding war — or negotiate instead.

The Short Version

A home inspector in Brampton looks for water, movement, fire risk, worn-out mechanicals, and bad air — roof to foundation, outside in, about four hours. The attic and the panel are where the surprises live. A finished basement is the one place a standard inspection can't fully see, so if there's any water history, add the mold test.

If you're under a conditional offer right now and want to know what a standard home inspection in Brampton covers and costs, that page has the full scope. Balwinder is InterNACHI certified, licensed and insured, and available across Brampton, Mississauga and the GTA.

Frequently Asked Questions

What are the biggest red flags in a home inspection?

Active water in the basement, horizontal or displaced foundation cracks, aluminum or knob-and-tube wiring, a furnace or roof at end of life, and mold staining in the attic. None of them are automatic deal-breakers. All of them are negotiation items with real prices attached.

How long does a home inspection take in Ontario?

Two to four hours for a detached house, depending on size, age, and how thorough the inspector is. Kirpa's standard inspection runs about four hours.

Do home inspectors check for mold?

A standard inspection looks for visible mold and moisture signs. Actual mold testing — air samples sent to a lab — is a separate service. At Kirpa it's $450–$750 with the lab work included.

Should I be there for the inspection?

Yes, at least for the last hour. You'll understand the report ten times better after walking the house with the inspector.

Can I use the home inspection to negotiate?

That's the main reason to get one. A report with a $12,000 roof and a $6,000 furnace on it is a price conversation, not a feeling.

Book a Four-Hour Inspection, Not a 90-Minute Walk-Through

Roof to foundation, attic entered, panel cover off, and a plain-English photo report you can actually negotiate with. InterNACHI certified, licensed and insured.

Serving Brampton, Mississauga, Toronto, and the surrounding GTA.

Book Your Inspection →

Or call (647) 474-5626